Editing Ross rifle
Warning: You are not logged in.
Your IP address will be recorded in this page's edit history.The edit can be undone.
Please check the comparison below to verify that this is what you want to do, and then save the changes below to finish undoing the edit.
Latest revision | Your text | ||
Line 116: | Line 116: | ||
==Military variants== | ==Military variants== | ||
<b>Rifle, Ross Mk I</b><ref name="Phillips, J. 2005"/> | <b>Rifle, Ross Mk I</b><ref name="Phillips, J. 2005"/> | ||
− | This was the first production military model Ross Rifle. The first | + | This was the first production military model Ross Rifle. The first 500 (made for Fish & Game) were fitted with the full-length folding <i>Sight, Ross Mk I.</i> Before any were delivered, the sight was replaced with a shorter version graduated to 2200 yards rather than 2500 yards. Years later, this sight would be designated <i>Sight, Ross Mk I*</i>. Later, many weapons would have this replaced with the <i>Sight, Ross Mk II</i>, a curved sliding "Land Vizier" type. The barrel was 28 inch long, and the fore-stock ended 4 inches short of the muzzle. The front band had a bayonet lug. The safety was operated by a square sliding button on the rear of the bolt handle. The magazine cut-off was on the lower right of the magazine protruding through the stock, and pressing it down engaged the cut-off. The magazine cut-off release was inside the front of the trigger guard, and depressing it would disengage the cut-off. A large lever was on the right side which was used to depress the magazine follower for "dump loading" all five rounds at once. The weapon was a straight-pull cock-on-close design. There was a sliding trap in the butt-stock for cleaning tools. A total of 10,500 were manufactured. A number of the original 500 were re-purposed as training rifles and fitted with longer front barrel bands used on later production <i>Rifle, Ross Mk II</i>. This was done so they could more easily endure the stress of constant bayonet practice. |
<b>Carbine, Ross Mk I</b><ref name="Phillips, J. 2005"/> | <b>Carbine, Ross Mk I</b><ref name="Phillips, J. 2005"/> | ||
Line 128: | Line 128: | ||
<b>Rifle, Ross Mk II with Sight, Ross Mk III</b><ref name="Phillips, J. 2005"/> | <b>Rifle, Ross Mk II with Sight, Ross Mk III</b><ref name="Phillips, J. 2005"/> | ||
− | <i>Sight, Ross Mk II</i> proved more fragile than desired, and it was replaced with a simpler version, the <i>Sight, Ross Mk III</i>. Instead of a curved bend to the slider, they employed a straight slider with curve-cut sides bent down. The official nomenclature for this model was <i>Rifle, Ross Mk II with Sight, Ross Mk III</i>. The 28 inch barrel was retained, the sight change being the difference. As before, further improvements would be introduced to production without bothering to change the designation. | + | <i>Sight, Ross Mk II</i> proved more fragile than desired, and it was replaced with a simpler version, the <i>Sight, Ross Mk III</i>. Instead of a curved bend to the slider, they employed a straight slider with curve-cut sides bent down. The official nomenclature for this model was <i>Rifle, Ross Mk II with Sight, Ross Mk III</i>. The 28 inch barrel was retained, the sight change being the the difference. As before, further improvements would be introduced to production without bothering to change the designation. |
<b>Rifle, Ross Mk II*</b><ref name="Phillips, J. 2005"/> | <b>Rifle, Ross Mk II*</b><ref name="Phillips, J. 2005"/> | ||
Line 134: | Line 134: | ||
<b>Rifle, Ross Mk II**</b><ref name="Phillips, J. 2005"/> | <b>Rifle, Ross Mk II**</b><ref name="Phillips, J. 2005"/> | ||
− | Development of this weapon began in the spring of 1908, and the planned designation was <i>Rifle, Ross Mk III</i>. This model was intended as a major improvement over the previous <i>Rifle, Ross Mark II with Sight, Ross Mk III</i>. The barrel length was extended to 30.5 inches, the rear hand-guard was simplified, the safety was replaced by a completely new flag-type safety, and the rear sight was changed to the third-party <i>Sight, Sutherland Mk I</i>. The magazine cut-off was dispensed with entirely. By the time it was ready to be produced in numbers, an even more radical design change was in the works to become the Mk III, and this model was desiginated <i>Rifle, Ross Mk II**</i> instead | + | Development of this weapon began in the spring of 1908, and the planned designation was <i>Rifle, Ross Mk III</i>. This model was intended as a major improvement over the previous <i>Rifle, Ross Mark II with Sight, Ross Mk III</i>. The barrel length was extended to 30.5 inches, the rear hand-guard was simplified, the safety was replaced by a completely new flag-type safety, and the rear sight was changed to the third-party <i>Sight, Sutherland Mk I</i>. The magazine cut-off was dispensed with entirely. By the time it was ready to be produced in numbers, an even more radical design change was in the works to become the Mk III, and this model was desiginated <i>Rifle, Ross Mk II**</i> instead. |
<b>Rifle, Ross Mk II<sup>3</sup>*</b><ref name="Phillips, J. 2005"/> | <b>Rifle, Ross Mk II<sup>3</sup>*</b><ref name="Phillips, J. 2005"/> | ||
− | This rifle was an adaptation of the <i>Rifle, Ross Mk II</i> to use the <i>Sight, Sutherland Mk II</i>. Some internal improvements were made as well. The original sliding button safety and the magazine cut-off were retained, along with the 28 inch barrel and the stylish older rear hand-guard. None of this model were newly manufactured. All were converted from <i>Rifle, Ross Mk II with Sight, Ross Mk III</i> or the later <i>Rifle, Ross Mk II<sup>4</sup>*</i> | + | This rifle was an adaptation of the <i>Rifle, Ross Mk II</i> to use the <i>Sight, Sutherland Mk II</i>. Some internal improvements were made as well. The original sliding button safety and the magazine cut-off were retained, along with the 28 inch barrel and the stylish older rear hand-guard. None of this model were newly manufactured. All were converted from <i>Rifle, Ross Mk II with Sight, Ross Mk III</i> or the later <i>Rifle, Ross Mk II<sup>4</sup>*</i>. |
<b>Rifle, Ross Mk II<sup>4</sup>*</b><ref name="Phillips, J. 2005"/> | <b>Rifle, Ross Mk II<sup>4</sup>*</b><ref name="Phillips, J. 2005"/> | ||
Line 143: | Line 143: | ||
<b>Rifle, Ross Mk II<sup>5</sup>*</b><ref name="Phillips, J. 2005"/> | <b>Rifle, Ross Mk II<sup>5</sup>*</b><ref name="Phillips, J. 2005"/> | ||
− | The last of the Mk II line would be produced using the <i>Sight, Sutherland Mk I</i> and simplified rear hand-guard of the <i>Rifle, Ross Mk II**</i>. The 28 inch barrel, sliding button safety, and magazine cut-off were retained | + | The last of the Mk II line would be produced using the <i>Sight, Sutherland Mk I</i> and simplified rear hand-guard of the <i>Rifle, Ross Mk II**</i>. The 28 inch barrel, sliding button safety, and magazine cut-off were retained. |
<b>Rifle, Ross Mk III</b><ref name="Phillips, J. 2005"/> | <b>Rifle, Ross Mk III</b><ref name="Phillips, J. 2005"/> | ||
− | For all practical purposes, the <i>Rifle, Ross Mk III</i> was an entirely new design. It incorporated the 30.5 inch barrel and flag safety of the <i>Rifle, Ross Mk II**</i>, taking that re-design much further. The internal double-stack magazine was replaced with an exposed single-stack magazine. The "dump loading" lever was gone, and a charger guide was added for loading with stripper clips. A magazine cut-off was employed, but the design that lowered the magazine shell was discarded and replaced by one that restricted the rearward travel of the bolt. The bolt-stop plunger was replaced by a flag lever with 3 positions (cut-off enabled, bolt release, cut-off disabled). The bolt was far sturdier and had multi-thread locking lugs. A new rear sight designated the <i>Ross Battle Aperture</i> was installed on the bridge of the receiver rather than on top of the barrel | + | For all practical purposes, the <i>Rifle, Ross Mk III</i> was an entirely new design. It incorporated the 30.5 inch barrel and flag safety of the <i>Rifle, Ross Mk II**</i>, taking that re-design much further. The internal double-stack magazine was replaced with an exposed single-stack magazine. The "dump loading" lever was gone, and a charger guide was added for loading with stripper clips. A magazine cut-off was employed, but the design that lowered the magazine shell was discarded and replaced by one that restricted the rearward travel of the bolt. The bolt-stop plunger was replaced by a flag lever with 3 positions (cut-off enabled, bolt release, cut-off disabled). The bolt was far sturdier and had multi-thread locking lugs. A new rear sight designated the <i>Ross Battle Aperture</i> was installed on the bridge of the receiver rather than on top of the barrel. |
<b>Rifle, Ross Mk IIIB</b><ref name="Phillips, J. 2005"/> | <b>Rifle, Ross Mk IIIB</b><ref name="Phillips, J. 2005"/> | ||
− | The British government chose to purchased a version of the <i>Rifle, Ross Mk III</i> with a far simpler rear sight known as the <i>War Office Pattern Sight</i> | + | The British government chose to purchased a version of the <i>Rifle, Ross Mk III</i> with a far simpler rear sight known as the <i>War Office Pattern Sight</i>. |
− | Note: A <i>Rifle, Ross Mk III*</i> may have existed, employing a strengthened action, new front barrel band, and different front sight. | + | Note: A <i>Rifle, Ross Mk III*</i> may have existed, employing a strengthened action, new front barrel band, and different front sight. One source mentioning it considers the designation dubious.<ref name="Hogg p177">Hogg and Weeks 2000, p. 177.</ref> |
==Military redesignations== | ==Military redesignations== | ||
Line 231: | Line 231: | ||
== Users == | == Users == | ||
*[[Canada]]<ref>Berton, Pierre. '' Vimy''. Anchor Canada: 2001.</ref> | *[[Canada]]<ref>Berton, Pierre. '' Vimy''. Anchor Canada: 2001.</ref> | ||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
*[[Luxembourg]]<ref>[http://www.mnhm.lu/pageshtml/virtualmuseumtour.php GRAND-DUCHY OF LUXEMBOURG]</ref> Issued to the Grand Ducal Guard in 1945, replaced by [[Lee–Enfield]] in the same year. | *[[Luxembourg]]<ref>[http://www.mnhm.lu/pageshtml/virtualmuseumtour.php GRAND-DUCHY OF LUXEMBOURG]</ref> Issued to the Grand Ducal Guard in 1945, replaced by [[Lee–Enfield]] in the same year. | ||
− | |||
− | |||
− | |||
− | |||
*[[United Kingdom]]<ref name="Hogg p175">Hogg and Weeks 2000, p. 175.</ref> – issued to the Royal Navy to free up Lee–Enfields for land use. | *[[United Kingdom]]<ref name="Hogg p175">Hogg and Weeks 2000, p. 175.</ref> – issued to the Royal Navy to free up Lee–Enfields for land use. | ||
− | |||
− | |||
== Resources == | == Resources == | ||
Line 258: | Line 244: | ||
== References == | == References == | ||
− | * | + | * Phillips, Roger F., François J. Dupuis and John A. Chadwick, ''The Ross Rifle Story'' (ISBN 0973241608) |
− | + | * "Huot", in Bernard Fitzsimons (general editor), ''The Encyclopedia of Twentieth Century Weapons and Warfare'' (Phoebus/BBC, 1978), Volume 13, page 1385. | |
− | + | * Duguid, A. Fortescue ''A Question of Confidence'' (Service Publications, 2002) | |
− | + | * Hogg, Ian V. and John S. Weeks. ''Military Small Arms of the 20th Century''. Seventh edition, Iola, WI, USA: Krause Publications, 2000. ISBN 0-87341-824-7. | |
− | + | * Phillips, R., Knap, J. Jerome, "Sir Charles Ross And His Rifle" (ISBN 0919316115) | |
− | + | * "Handbook For The Canadian Service Rifle, Ross Mk III, 1913 Pt I and II" HQ 70-55-41 – 37765-11-1 | |
− | + | * "The Ross Rifle Sporting Catalogue 1909" Cornell Publications | |
− | + | * "The Ross Rifle Catalogue 1912" Cornell Publications | |
− | * | + | * "Arctic Airmen" Kimber London 1987 |
− | + | ||
− | + | ||
− | + | ||
− | * Duguid, | + | |
− | + | ||
− | + | ||
− | * Hogg, Ian | + | |
− | * Knap, Jerome, " | + | |
− | * | + | |
− | * | + | |
− | * | + | |
− | * | + | |
* Rawlings, Bill. ''Trench Warfare: Technology and the Canadian Corps 1914–1918''. (University of Toronto Press, 1992). | * Rawlings, Bill. ''Trench Warfare: Technology and the Canadian Corps 1914–1918''. (University of Toronto Press, 1992). | ||
− | * | + | * Walter, John, ''Rifles of the World'' third edition (Krause Publications, Inc. 2006) (ISBN 0-89689-241-7). |
− | + | * Hamilton, Douglas T., "Manufacturing the Ross Rifle and Press-Button Knife" in ''Machinery Magazine, October, 1911'' (Reprinted by Lindsay Publications Inc. 2006, ISBN 1-55918-344-6). | |
− | * | + | * Austerman, Wayne R., "Weapon that Failed" in ''Military History, April, 1991'' (Stivers Pubishing, 1991). |
− | * | + | * Scarlata, Paul, "The Canadian Ross Straight-Pull Military Rifles" in ''Man at Arms, April 1999'' (National Rifle Association) |
− | * | + | * Carlyle, Randolph, "Our National Arm" in ''The Canadian Magazine, Vol.XXXI, May 1908 - October 1908, inclusive'' (The Ontario Publishing Co. Limited, 1908) |
− | * | + | * ''Official Report of the Debates of the House of Commons of the Dominion of Canada, Fourt Session - Tenth Parliament 7-8 Edward VII 1907-1908, Vol. LXXXVI, 12 May - 10 Jun 1908, inclusive'' (S.E. Dawson, Printer). |
− | + | * Bodinson, Holt, "Sir Charles Ross and His Straight Pulls" in ''Guns Magazine, November, 2012'' (Publishers Development Corporation, 2012) | |
− | + | * Crossman, Edward C., "The Rifle of My Dreams" in ''Arms and the Man'' magazine (Reprinted by Ross Rifle Company in ''The Ross Rifle'' 1912) | |
− | * | + | * Stent, H. V., "Ross Rifle Ruckus" in ''Guns Magazine, May 1958'' (Guns Magazine, Skokie Il, 1958) |
− | * | + | * Scarlata, Paul, "The Remarkable Ross" in ''Gun Digest, 68th edition (F+W Media, 2014, ISBN 1-4402-3542-2) |
− | * | + | * Canfield, Bruce N., ''U.S. Military Bolt Action Rifles'' (Mowbray, 2010, ISBN 1-931464-43-X) |
− | * | + | * Canfield, Bruce N., ''U.S. Infantry Weapons of the First World War'' (Mowbray, 2000, ISBN 1-917218-90-6) |
− | * | + | * Webster, Donald B., ''Military Bolt Action Rifles 1841 - 1918'' (Museum Restoration, 1993) |
− | * | + | |
== External links == | == External links == | ||
Line 300: | Line 273: | ||
* [http://www.canadiansoldiers.com/weapons/rifles.htm?title=Bayonets Ross Bayonets at www.canadiansoldiers.com] | * [http://www.canadiansoldiers.com/weapons/rifles.htm?title=Bayonets Ross Bayonets at www.canadiansoldiers.com] | ||
* [http://www.rossrifle.com/ RossRifle.com] | * [http://www.rossrifle.com/ RossRifle.com] | ||
− | |||
* [http://www.youtube.com/watch?v=EaSui_UqDX8 Forgotten Weapons – Myth and Reality of the Ross MkIII Rifle] | * [http://www.youtube.com/watch?v=EaSui_UqDX8 Forgotten Weapons – Myth and Reality of the Ross MkIII Rifle] | ||
* [https://canadaatwarblog.wordpress.com/2015/04/21/cefs-ross-rifle-fiasco-responsible-for-countless-of-casualties-fact-or-myth/ "CEF’s Ross Rifle Fiasco, Responsible For Countless Of Casualties Fact or Myth!"] Canada at War Blog, [[April 21]], [[2015]]. | * [https://canadaatwarblog.wordpress.com/2015/04/21/cefs-ross-rifle-fiasco-responsible-for-countless-of-casualties-fact-or-myth/ "CEF’s Ross Rifle Fiasco, Responsible For Countless Of Casualties Fact or Myth!"] Canada at War Blog, [[April 21]], [[2015]]. |